How To Repair Cane Chair
Just it was such a good bargain! I can prepare that…I think. Things I tell myself when I come across a killer garage auction find. Refinishing the kitchen table, piece of cake. Re-covering the chairs and painting them, slice of block. Fixing the torn cane backing on some of the chairs. Um..sure? Why not requite it a shot? A great opportunity to learn a new skill or to let you see me fail miserably. Either way, it's a learning feel.
Easing myself into the project, I kickoff refinished the table. Run into that project hither. Then it was time to offset on the chairs. First things showtime, remove the chair seats and recover. Due to the high contrast design stenciled on the kitchen island, I went with a solid color textured fabric to avert visual overload. See how to re-embrace a chair seat here. Most of the chair frames only needed a cleaning, a little sanding on dings, and so a few coats of paint. Three chairs had varying degrees of harm to the cane backs.
Starting time, let's define some of the tools and the substitutes I used. Having a kid in higher, I was not near to spend a fortune on tools for one chair so I got creative.
Pikestaff Webbing
The pre-woven cane used to supplant the cane in chairs with a groove. Utilizes spline and mucilage to hold pikestaff webbing in place instead of the chair back style with the holes that the cane is strung through. There are different types of weave, see the film below I institute on Pinterest. Unfortunately, the photo didn't have a link to the source and with no watermark, it is tricky to rails down. Let me know if you know the source for this photo!
Caning Wedges
Small hardwood wedges used to button the cane webbing into the groove in the chair and to anchor it in place. You can find them on Amazon for about $vii for a set of five. Again, I didn't desire to spend a fortune fixing these chairs and then I improvised with small spatulas. Because why wouldn't you employ spatulas as a substitute? I realize that if my husband used the Pampered Chef spatulas on a dwelling house repair project then I would be super annoyed. Since they are my spatulas, I went for it and the spatulas were non harmed in whatsoever way.
Hide Glue
Adhesive that is fabricated from animal connective tissues. The collagen is a protein molecule that is very stiff in this glue and it has no VOCs, dries clear and yous can add more hibernate gum to it rather than having to remove the old mucilage when doing repairs. The downside is that I wasn't able to pick any upward at my local store. A instance of hide gum could exist bought online but I didn't need that much. Amazon also had it simply it was similar $17 for a bottle and not Prime commitment then I opted to just use wood glue. Deplorable if y'all are a article of furniture purist and this causes you lot concrete pain. Although if yous are a furniture purist (aka craftsman), you probably aren't here reading this blog.
Spline
Reed that is specially shaped to fit into the groove that anchors the cane webbing into a chair'due south seat frame. When ordering, order a foot more than than you lot need to allow for cuts or mistakes. When choosing spline for the chair, pick a spline that fits loosely plenty in the groove when information technology is dry that y'all don't need to pry it out.
Spline Chisel
A tool with a curved stop used to remove the quondam spline from the chairs. If you tin not notice a spline chisel, or don't want to club one, a small flat caput screwdriver works really well.
Pre Caning Instructions
Remove the chair seats; usually in that location are screws property them on to the chair frame. Flip over the chairs and remove the screws and go on the screws in a container or plastic baggie for safety keeping.
Re-comprehend the chair seats in a cloth of your choosing. Like I mentioned before, I didn't want too many prints clashing in the kitchen, so I kept my cloth a solid color with a repeating texture like to the patterns in the light fixture, the cane webbing on the chairs, and the window valances. Four judge clear vinyl sheeting was purchased to comprehend the cloth simply afterwards I did the first chair seat my 13 year old son commented, with a completely straight face, "And then yous're slowly turning this into an old lady firm, huh?" Apparently my ego couldn't have the onetime lady comment so I removed the plastic and opted to Scotchgard the textile instead.
"Onetime Lady firm", pfft.
Evaluate damage to the chairs. There were three levels of impairment to the caning on different chairs. I was minimal and only needed a few errant strands of caning tucked back in identify and re-glued. The little screwdriver helped to poke private pieces in place. The second chair had the cane webbing that had pulled out of the groove but was not damaged. I gently lifted the loose spline and placed the loose cane back in the groove, added glue, popped the spline back in place, and so clamped 24 hours until dry. The third chair had caning that was damaged beyond a simple set. Here's how to replace the caning on a chair.
Supply List
- Pikestaff webbing to match existing chairs
- Wood glue or hide mucilage
- Small flat head spiral driver or caning tool
- Clamps
- Additional spline, if needed
- Large sink or tub to soak cane fabric
- Tarp or towels
- Caning wedges or pocket-sized spatulas
- Hammer
- Spline chisel or utility knife
- Scissors
- White Vinegar, if glue does non release easily
Instructions
Stride 1:
Advisedly pry loose the spline by gently running a utility knife along either side and lift out with the spline chisel or small flat head screwdriver. If the spline is stuck, it may exist the hide glue won't loosen. In that case, make a solution of equal parts warm water and white vinegar to soak the spline. Be sure there is a tarp or towels down so your flooring or work surface doesn't get damaged. Remove the old spline and cane. Let chair dry before continuing.
Step 2:
Pull out the old cane, hopefully in one slice. This onetime cane webbing can be used as a pattern for the new cane webbing. Clean out the groove to remove dirt, pikestaff pieces, one-time gum, etc.
Step 3:
Soak the new pikestaff webbing in warm h2o for 30-60 minutes. The bathtub works really well for this. I soaked the cane webbing for 40 minutes, but information technology could have used a few more minutes. Let drip dry on a towel for iii minutes.
Step 4:
Lay the old pikestaff webbing over the new cane webbing, being sure to line upwards the weave. Cut it a half inch or more larger than the sometime cane webbing. If this was textile, I would say to leave a half inch or more seam assart. It is recommended to cut with the chisel, but I didn't desire to have that long and have the cane webbing dry. I used scissors instead and information technology cutting beautifully.
Step 5:
Place the trimmed pikestaff webbing over the back of the chair and align so that it is directly and covers the groove in the chair back past at to the lowest degree a one-half inch. Use the wedges, or spatulas, to button the cane webbing in role way. Don't exist too aggressive, you don't want the cane to interruption.
Use the same process as recovering the chairs or if y'all were stretching canvas over a frame. In other words, push button down a modest section of cane into the groove on ane side and then practise the same to the opposite side. This keeps the pikestaff from shifting and getting wonky. Ease it in by gently pushing the cane in the groove role way. Work your manner around the perimeter of the chair in the groove. Y'all can leave ane spatula wedged in as you work on the opposite side.
Repeat this process and push the cane webbing farther downward into the groove.
Step 6:
Once the cane has been pushed into the groove, cut off the backlog strands of cane. A spline chisel and hammer can be used to gently do this, be sure to not damage the woods frame. I used the utility pocketknife and gently pressed it confronting the pikestaff and it cut easily. Trim excess cane all the mode around the chair back.
In the meantime, put the spline in the warm water for near 10 minutes to soften.
Step vii:
Add glue in the cane filled groove all around the perimeter of the chair back. Hide mucilage may be used, but I had forest glue and then that is what I used. The layers of paint will also help concur the cane and spline in place once dried.
Step eight:
Remove the spline from the water and let baste dry out for a minute or two.
Supersede the spline into the groove in the chair. The beauty of using the old spline is that it is the perfect length and basic shape already. Start with the top center of the chair, contrary the cutting ends of the spline, and piece of work around. Button the spline in the groove as all-time yous tin can. Use a wet wood cake between the spline and a hammer to knock it in identify without damaging the spline.
If using new spline, start at the lesser and work your manner effectually a rounded chair. If the chair has a square back, cut the spline to fit each straight length of the grooves and miter the corners for a nice fit. Gently tap in identify. A sharp utility knife works well to cutting the spline.
Pace 9:
Wipe off whatever backlog glue and cut off any pieces of cane that are too long and stick out. Employ clamps around the perimeter of the chair to agree the spline in the groove. Permit dry out for 24-48 hours. DO Not put out in the sun to dry!
Step 10:
In one case the cane webbing is repaired and the glue is dry, pigment your chairs. Sand any dings or nicks in the chair that need smoothing out, degloss with Liquid Sandpaper and wipe off with a make clean, dry cloth. Paint chairs. It took 3 coats of white paint to fully cover my chairs.
TIP: Apply paint on one side of the cane webbing with the pigment brush and use a sponge on the reverse side to immediately wipe and spread any paint drips.
When painted chairs are completely dry out, re-attach the seat cushions with the screws or bolts. Wait at least a week before the chairs are in use so the paint has enough of time to cure, or harden.
I'g loving how these chairs turned out. The previously dark and heavy feeling of the kitchen chairs has been replaced with lighter and brighter versions of their best selves. Beingness slightly nervous to endeavour something I had never earlier done, I think my caning conviction has grown after this projection.
I only love fixing up and refinishing erstwhile furniture. Maybe it is getting quality furniture for inexpensive? Maybe it is the procedure that proves nothing is beyond fixing? Mayhap I just similar the claiming? I don't know. I just kind of like the feeling of hope a refinished piece gives me that no matter how worn or tattered something is, with a fiddling TLC, information technology tin smooth again and still be loved by someone. Being able to look effectually and run into all the furniture pieces that take been saved and carefully worked on helps me make a house a dwelling house.💙
Related Set 'Em Up Posts
Farmhouse Kitchen Table
Stenciled Kitchen Isle
How To Re-Comprehend a Chair Seat (video)
Finding the All-time Style to Polish Brass (Video)
How To Replace a Bathroom Faucet
Replacing Furniture Hardware
Stenciled Dining Table
Teenage Boy Cheap Bathroom Update
Change the Look of Your Lamp in Minutes
Dining Room Buffet Piece of furniture Makeover
Spray Painted Rattan Chairs
Our Flooring Remodel Adventure Begins
Demo and Installation of Wood Look Tile
How To Fix a Hole in a Hollow Core Door (video)
Fixing Peeling Leather Chairs (video)
Caulking Baseboard Similar a Pro
Source: https://tingedblue.com/cane-back-chair-makeover/
0 Response to "How To Repair Cane Chair"
Post a Comment